#BEHRINGER X32 LIVE STREAMING SETUP HOW TO#
#BEHRINGER X32 LIVE STREAMING SETUP UPGRADE#
#BEHRINGER X32 LIVE STREAMING SETUP PRO#

Are you saying that the audio and video are out of sync with one another when watching the live stream? If so, that could be the sample rate mismatch I mentioned earlier but it might also be the hardware struggling, like you mentioned. You mention that audio and video are 'off'. Sometimes a mismatch in sample rates can cause things to change pitch. Make sure your X32 is set to a 48kHz sample rate. That could be some issue with the audio signal being sent to the device, Switcher Studio, your iPad, or the interface you use to get audio into the iPad. Now, as far as you sounding like a chipmunk. One of the best explanations I've seen about this is from the late Andrew Stone at Church on the Move in Tulsa. These are microphones, usually placed near the back of the room, that help pick up the audio as it sounds to someone that is in the room. In other words, you're only hearing the direct audio and not the audio like it's happening in the room.ДЄ great way to bridge that gap is to use ambient microphones that are mixed into your online/broadcast mix only. If it sounds good in the room but not online, that usually means your online/broadcast audio mix is lacking the context of the room itself.

#BEHRINGER X32 LIVE STREAMING SETUP UPGRADE#

That is something that will be important no matter what gear you choose to upgrade to, and it's also the most important part for people watching the stream. I'll do my best to take this step by step.ДЇirst, I would suggest working on your audio. We are open to doing that, but our budget is not huge on this sort of thing.ДЄt any rate, grateful for any suggestions you can offer! Maybe we need to bit the bullet and buy a Black Magic ATEM, and a Black Magic 4k camera. We are a small church, with a small budget, but would like to take some steps to make our livestream better. When we run bandwidth checks on our WiFi, it seems like it is up to the challenge. from the soundboard, ProPresenter slides, and two video sources). However the Switcher Studio App does not allow us to record in 4k on the iPad or use the wide angle lens.ДЄll that to say, I think one of our problems is a hardware issue - we do not actually have an 'encoder.' So my guess is some of the reasons our audio is off, and our video is off, is because our little setup is working really hard to process all the information we are sending to it (e.g. Both the iPhone and the iPad function as cameras. We us a iRig Pre HD to connect the audio coming out of our sound board (Behringer X32) to our iPad (which has the switcher app - 'Switcher Studio').

#BEHRINGER X32 LIVE STREAMING SETUP PRO#

Our current setup uses an iPhone 6 and also a iPad Pro 2020 (with a 'Switcher Studio' app).

SECOND, our other problem is the quality of the video image online.

#BEHRINGER X32 LIVE STREAMING SETUP HOW TO#

We have had a little better luck with audio, since we have learned how to create two separate mixes, one for in-house, and one we send online, but for some reason the quality is not great. On the iPad Pro we use the App 'Switcher Studio,' through which we send our livestream to Facebook (or YouTube). There have even been times where I sound like Alvin the Chipmunk online while I am preaching! We use a Behringer X32 as a soundboard, so we send the audio from that, through and iRig Pre HD, to an iPad Pro (2020). This isn't always the case, but it happens enough to annoy. Often the audio sounds good in-house (in the church building itself), but sounds different online.

Our issues are twofold.ДЇIRST, we struggle to get good audio on our online livestream service. Before I got here the church did their best to produce a livestream service, which they stream to Facebook. Long story short, I recently became the new pastor of a smaller church in Wisconsin (about 100 people per Sunday). You have amazing resources and really great content! I heard about your website and resources through ProChurch tools.

Behringer x32 live streaming setup